How much thin-set for 80 ft² of 6×6″ tile on a concrete slab?
| Bags (setting the tile) | 2× 50 lb |
|---|---|
| Total weight | 100lb |
| Trowelchosen by the 6″ tile, not by the room | 1/4″ × 3/8″ square notch |
| Coverage per bag75 ft² at this notch depth | 75ft² |
| Back-butteringtrowel ridges alone will collapse to full coverage | Not needed |
| Substrate | Concrete slab |
| Mortar type | Standard modified thin-set (ANSI A118.4) |
Notes
- The trowel decides the quantity, and the tile decides the trowel. A 1/4″ × 3/8″ square notch lays down enough mortar for 6″ tile; using it over 80 ft² takes 2 bags. The same floor in 2″ mosaic would need a fraction of that, and a generic "bags per square foot" figure is wrong for both.
- At 6″ the trowel ridges collapse into full contact when you set and slide the tile. Pull one up early in the job and look at the back — you want the ridges flattened, not standing.
- Concrete slab is a straightforward substrate for this. Clean, flat and structurally sound matters more than the mortar you choose.
- Mix it and let it slake. Almost every bag says mix, wait 5–10 minutes, then remix — that rest is what lets the polymers hydrate. Skipping it is why mortar sometimes will not hold a tile on a wall.
- Only spread what you can set in about 15 minutes. Mortar that has skinned over looks fine and bonds to nothing; touch it with a finger and if it does not come away wet, scrape it off.
The trowel decides the quantity
Not the room. A 1/4″ × 3/8″ square notch is what 6×6″ tile needs, and at that notch depth a 50 lb bag covers about 75 ft². Over 80 ft² that comes to 2 bags.
The same floor in 2″ mosaic would take a fraction of this. Any figure quoted as "bags per hundred square feet" without asking the tile size is a guess.
Back-buttering: not needed
ANSI A108.5 wants 80% mortar contact for interior floors and 95% for wet or exterior work. Above about 15″, no trowel alone gets there — the ridges do not collapse fully under a tile that size, and the corners end up hollow. Where it is required, the extra 30% is already in the bag count above.
Pull a tile up early in the job and look at the back. You want flattened ridges across the whole face, not a stripe pattern.
Concrete slab
Mortar for this substrate: Standard modified thin-set (ANSI A118.4).
Two habits that decide whether it holds
Let it slake. Almost every bag says mix, wait five to ten minutes, remix — that rest is what lets the polymers hydrate, and skipping it is why mortar sometimes will not hold tile on a wall.
Only spread what you can set in fifteen minutes. Mortar that has skinned over looks perfectly fine and bonds to nothing. Touch it; if your finger does not come away wet, scrape it off and start again.
Nearby sizes
- How much thin-set for 60 ft² of 6×6″ tile on a concrete slab?
- How much thin-set for 100 ft² of 6×6″ tile on a concrete slab?
- How much thin-set for 50 ft² of 6×6″ tile on a concrete slab?
- How much thin-set for 120 ft² of 6×6″ tile on a concrete slab?
- How much thin-set for 80 ft² of 4×4″ tile on a concrete slab?
- How much thin-set for 80 ft² of 12×12″ tile on a concrete slab?
- How much thin-set for 80 ft² of 3×6″ subway tile on a concrete slab?
- How much thin-set for 80 ft² of 12×24″ tile on a concrete slab?
Read more
- Thin-Set Mortar Cost per Bag and per Square FootA bag of thin-set is nine dollars. How many bags you need is decided by the notch on your trowel, not by the tile.
- How Many 12×12 Tiles in 100 Square Feet? 100 — Then Buy 110The arithmetic gives a round number that is right and not enough. Two things separate the count from what you should put in the trolley.
- How Much Extra Tile to Buy: 10%, 15% or 20% — and What Sets the NumberWaste percentage is not a safety margin. It is a prediction about how many cut tiles produce a usable second piece, and the pattern decides it.
- What Size Trowel for Tile? Match the Notch to the Tile, Then Check the BackThe chart gets you to the right aisle. What settles it is lifting one tile and looking at how much mortar actually touched it.